Last Post |
Vic Roberts
|
|
Edward Rose
|
7/2/2021 8:06 PM
|
Hi Vic!
Yes: your design was part of my inspiration!
Ed
In a message dated 7/2/2021 4:49:08 PM Pacific Standard Time, ensignsailing@ensignclass.com writes:
Ed & Kristen,
When I received #2032 from Ensign Spars in 2014, it had the Jib Halyard tensioning system shown in the attached photo, which seems to be the same design used by you, Ed.
I can get better photos and perhaps model numbers for the two triple blocks and one single block on Sunday.
Vic Roberts
#2032
Attachment(s): IMG_1587.JPG (3.6 MB)
|
|
|
Vic Roberts
|
7/2/2021 7:48 PM
|
Ed & Kristen, When I received #2032 from Ensign Spars in 2014, it had the Jib Halyard tensioning system shown in the attached photo, which seems to be the same design used by you, Ed. I can get better photos and perhaps model numbers for the two triple blocks and one single block on Sunday. Vic Roberts #2032
|
|
|
Edward Rose
|
7/2/2021 6:51 PM
|
Hi Kristen,
That would be nice, but I really don't have the time to talk. We're taking care of a family member that requires our undivided attention. It has been a pleasure trying to remember what I did during the restoration of my own boat, but unpickling the boat or unboxing all the parts to find what kind of fasteners or hardware I used is quite beyond me for now.
I'm sure there are many other active Ensign sailors who would love to help you out!
Best,
Ed
In a message dated 7/2/2021 11:05:39 AM Pacific Standard Time, ensignsailing@ensignclass.com writes:
Can I call you ? I am on 617 571 4854.
|
|
|
Edward Rose
|
7/2/2021 6:43 PM
|
Hi Kristen,
First, let me say I have only sailed my boat in the configuration depicted in my sketches a few times and have found my design choices to be largely satisfactory. I planned, then installed all the jewelry then sailed it for 2 months (in patchy primer!) to test out all my designs and choices. I then disassembled the boat to prepare for any changes and final finishing. Things got sidetracked by life and the boat is currently pickled and waiting for a new shop to be built.
So, would I use the Cunningham set-up in place of the Jib Halyard tensioning? No...I wouldn't...
I did extensive research into how to replace the Magic Box so many have used, but is no longer available. The design I settled on works well enough, so I have no plans to make any changes. If you race, you'll want the set-up that gives you the same degree of adjustment the old MB provided. The set-up I use for tensioning the Cunningham is crude by comparison, so, IMHO, is not suitable for the Jib Halyard.
Ed
In a message dated 7/2/2021 10:18:50 AM Pacific Standard Time, ensignsailing@ensignclass.com writes:
Could your cunningham block and tackle be used for the jib halyard tension set up?
|
|
|
Edward Rose
|
7/2/2021 6:13 PM
|
In a message dated 7/2/2021 9:56:10 AM Pacific Standard Time, ensignsailing@ensignclass.com writes:
... and the length of line required for each one of your block assemblies? We are just going to copy your set up in hopes that it is a fleet-wide reference....
|
|
|
Edward Rose
|
7/2/2021 6:09 PM
|
Hello Kristen,
First, let me say that no, I cannot tell you specifically what fasteners I used for the cabin top controls or for any other hardware. The sketches I put together and published simply document what I installed on my boat and, as you have already surmised, does not specify preparation of components or assembly instructions. Since I am only restoring one boat, there is no need to document to that level of detail. The good folks at Ensign Spars (past and present) would be a good source of specific information if you can't figure it out on your own. I believe the only person I asked about fasteners was Chad (formerly of Ensign Spars) about what size rivet to use when re-attaching the Sheer Clamp (3/16 X 1/2 every 6 inches for a total of 124 !!).
What I can offer is, I used best practices for fastening deck equipment as garnered through experience, asking more experienced heads (as you are doing), the many good books written about restoring boats and Google! Best practice here includes; how to prepare the structure you're mounting to, diameter hole to drill and bevel for any given fastener, number and type of washers, type of nut, thread lock, thickness of backing plate, sealant, dissimilar metals treatment, how many threads to leave showing and recommended tightening for the application.
During the planning for my boat's restoration, I built-up a fastener inventory by accounting for all the manufacturer recommended fastener diameter sizes, then determined the most common thread count that accommodated the widest range of lengths for that particular fastener as offered by the supplier and then purchased my best-guess lengths in batches of 10-to-100 depending on use.
As an example, I settled on 10-32's for all my #10's in both Black Oxide and plain finish. I settled on the 18-8 grade whenever I could find it and have a variety of lengths, ranging from 3/4" all the way up to 2-1/2". I think I used 5 different #10 lengths to account for all the different hardware mounted all over the boat. In the case of the Harken 459's, I had to use at least 2 different bolt lengths due to variation in the cabin top thickness on my boat.
Sorry I couldn't offer more help...you'll have to do your own study and revel in the experience!
Ed
In a message dated 7/2/2021 9:49:42 AM Pacific Standard Time, ensignsailing@ensignclass.com writes:
Fantastic! I guess my last question would be: do you have the specs for the nuts and bolts you used?
|
|
|
Kristen Standish
|
7/2/2021 2:05 PM
|
Can I call you ? I am on 617 571 4854.
|
|
|
Kristen Standish
|
7/2/2021 1:16 PM
|
Could your cunningham block and tackle be used for the jib halyard tension set up?
|
|
|
Kristen Standish
|
7/2/2021 12:56 PM
|
... and the length of line required for each one of your block assemblies? We are just going to copy your set up in hopes that it is a fleet-wide reference....
|
|
|
Kristen Standish
|
7/2/2021 12:49 PM
|
Fantastic! I guess my last question would be: do you have the specs for the nuts and bolts you used?
|
|
|
Edward Rose
|
7/1/2021 3:43 PM
|
Hi K,
Yes; I get my stainless steel black oxide fasteners from Fastener Express and most of my other fasteners from Bolt Depot. I make all my backing plates from G10 FR4 glass epoxy sheet. I bed all deck hardware, deck plates and indeed anything that fastens to the boat using butyl tape.
Hope that helps!
Ed
In a message dated 7/1/2021 10:13:13 AM Pacific Standard Time, ensignsailing@ensignclass.com writes:
Hi
Do you have the details concerning the nuts, bolts and backing plates you used for the cabin top hardware?
Thanks for your help.
K
|
|
|
Kristen Standish
|
7/1/2021 1:13 PM
|
Hi Do you have the details concerning the nuts, bolts and backing plates you used for the cabin top hardware? Thanks for your help. K
|
|
|
Gay De Hart
|
5/18/2021 5:33 PM
|
I am planning to use one on the forward bulkhead, and one in the cabin seat, to check on flotation so non-skid shouldn’t be an issue, but good to know the difference! I’ll let you know how they work out. Ron and Ed—great tips on hole cutting. Thanks. Gay Freestyle #383
|
|
|
Edward Rose
|
5/18/2021 5:23 PM
|
I used a Dremel circle arm saw with a milling bit... Easy and clean!
In a message dated 5/18/2021 2:10:59 PM Pacific Standard Time, ensignsailing@ensignclass.com writes:
I added two of those, from WM, the four-inch variety, to the stern so I could access traveler hardware. I was very satisfied. Be sure to order the correct holesaw. A round Holesaw mounted on an electric drill gives a perfect size opening. Well worth the additional expense, even if you have a jigsaw already.
Sent from my iPhone
|
|
|
Edward Rose
|
5/18/2021 5:13 PM
|
Hello Gay,
It looks like the West Marine deck plate doesn't have the diamond non-skid molded-in like the Beckson. I love the Beckson plates and recommend them. If you go with the West Marine version, let us know what you think!
Ed
In a message dated 5/18/2021 2:02:03 PM Pacific Standard Time, ensignsailing@ensignclass.com writes:
|
|
|
Ronald Wright
|
5/18/2021 5:08 PM
|
I added two of those, from WM, the four-inch variety, to the stern so I could access traveler hardware. I was very satisfied. Be sure to order the correct holesaw. A round Holesaw mounted on an electric drill gives a perfect size opening. Well worth the additional expense, even if you have a jigsaw already. Sent from my iPhone
|
|
|
Gay De Hart
|
5/18/2021 5:00 PM
|
I was wondering if you think the Beckson Deck Plates are the only way to go or would the West Marine equivalent work just as well? https://www.westmarine.com/buy/west-marine--6-screw-in-deck-plate--11743036
After shipping, the Beckson are a bit more expensive and I have a local West Marine I can go to so don't pay shipping.
|
|
|
Edward Rose
|
2/18/2021 12:46 PM
|
Hello David,
Seriously? You're owned by TWO Ensigns?!! You're a brave man... :-)
The material you reference is G10-FR4. It's fiberglass infused with epoxy resin, usually sold in sheets and is available in multiple thicknesses and sheet sizes. I use it in projects on my boat and like it for it's strength and fondness for bonding well with it's brethren :-) ...
One caveat: While FR4 is excellent and proven for backing plates, I have not sea tested any of the brackets I've made of FR4, only done static pull and twist tests. When I get my boat back out on the water next year, I suspect things will hold together just fine, but you never know! You guys will be the second to know how they perform.
Thanks,
Ed
"Eraser" #1484 (that's for you, Vic! :-)
In a message dated 2/18/2021 7:10:34 AM Pacific Standard Time, ensignsailing@ensignclass.com writes:
THANKS !! to all who have provided information in re this POST, with special appreciation to Ed Rose for the fantastic detailed drawings and pictures, and to Vic Roberts for facilitating providing the materials to the ECA platform.
One additional question I have, for Ed, relates to the “Green Material” used for various purposes in the project. Is it “G10 and FR4 glass cloth reinforced epoxy..” in some form/size… or something else? If you could provide any information in that regard, and or sources for it, I would appreciate it. And if that information was already included in the drawings/plans/pics, and I missed it I apologize in advance.
With appreciation.
Sincerely,
David
/ “EMERITUS”/ #1144 & “SABBATICAL”/ #1569 at .. david.ringsmuth@csun.edu
|
|
|
David Ringsmuth
|
2/18/2021 10:09 AM
|
THANKS !! to all who have provided information in re this POST, with special appreciation to Ed Rose for the fantastic detailed drawings and pictures, and to Vic Roberts for facilitating providing the materials to the ECA platform. One additional question I have, for Ed, relates to the “Green Material” used for various purposes in the project. Is it “G10 and FR4 glass cloth reinforced epoxy..” in some form/size… or something else? If you could provide any information in that regard, and or sources for it, I would appreciate it. And if that information was already included in the drawings/plans/pics, and I missed it I apologize in advance. With appreciation. Sincerely, David / “EMERITUS”/ #1144 & “SABBATICAL”/ #1569 at .. david.ringsmuth@csun.edu
|
|
|